Banner Finishing Explained: Hems, Grommets and Why Wind Slits Often Backfire
A banner's durability is built in twice: once in the material and again at the edges. Here is how to specify both for the wind and the timeline you actually face.
Where banner strength actually comes from
A vinyl banner is two layers of engineering working together. The film carries the printed image, and buried inside it is a scrim: a woven mesh of yarn that does most of the work of resisting tears. When a banner fails outdoors, it is rarely the ink that gives up first. It is the material tearing at a stress point, or an edge pulling away from its hardware.
Three terms on a material spec sheet tell you how a banner is built:
- Weight, listed in grams per square meter (gsm) or ounces per square yard. This describes how much material is in the sheet overall.
- Denier, a measure of how heavy the individual yarns in the scrim are. Heavier yarns make a mesh that is harder to rip.
- Scrim construction, how those yarns are arranged in each direction of the weave.
For a concrete reference point, Avery Dennison's data sheet for its MPI 4330 heavy duty double sided banner describes a 680 gsm (20 oz) film with a 1000 by 1000 denier scrim, rated for outdoor life of up to 3 years unprinted. Two details in that line matter. The 1000 by 1000 figure tells you the scrim is equally heavy in both directions of the weave. And the durability rating is for the material unprinted, so it describes the base media, not a promise about your finished, printed banner. If service life matters to your project, ask your printer what to expect once the banner is printed and installed in your conditions.
Material is only half the story. The other half is finishing: what happens at the edges, where the banner is folded, sewn or fused, and where the hardware goes in. A heavy material with weak edges can still fail, and a light material with careful finishing can be perfectly adequate for a short indoor job.
Hem styles and what each one trades off
A hem is the edge of the banner folded back on itself and secured, which doubles the material along the perimeter where stress concentrates. According to Avery Dennison's bulletin on creating digitally printed banners, hems can be made in five ways:
- Stitched: the fold is sewn down with thread. This is the familiar finish on most outdoor banners, and the stitch line is visible on the face.
- Stitched with webbing: a strip of woven reinforcing tape is sewn into the fold. The webbing gives grommets something tougher than vinyl alone to bite into along the edge.
- Stitched with rope: a rope is sewn inside the hem. This lets the banner be tensioned along its edge, which is useful when it is stretched between poles or across a frame rather than hung from a few points.
- Taped: the fold is held with double-sided tape designed specifically for hemming. There is no stitch line on the face, which some people prefer for a cleaner look on indoor displays.
- Welded: the fold is fused with heat so the two layers become one, again without visible stitching.
The practical trade-off is between appearance, how the banner will be mounted, and how much punishment the edge must take. Webbing and rope add reinforcement and change how the banner can be hung. Taped and welded hems keep the face clean. Each shop has its own capabilities and preferences here, so name the hem style you want on your request, and if you are unsure, describe the installation and ask which hem the printer recommends for it.
Hem width and what it means for your file
The same Avery Dennison bulletin puts a typical hem at around 50 mm (1.969 inches), and notes that a 50 mm hem needs 100 mm (3.937 inches) of material folded in half, with the fold going to the back of the banner.
That fold has consequences for your artwork. The hem band along each finished edge is doubled material, often with a stitch line running through it and grommets punched into it. Anything important that sits in that band can end up crossed by thread, pierced by hardware or partly hidden. Keep logos, phone numbers, web addresses and QR codes well clear of the edges, and treat the outer band of the design as background only.
How the hem allowance is handled in the file varies from printer to printer. Some want the extra material built into your artwork; others add it themselves. Do not guess. Ask the shop how it wants hems accounted for, and check the guide to preparing files for large-format printing and the artwork and file guidelines page before you export. Getting this wrong is one of the quieter ways to end up with a banner that is the wrong finished size or has text running into the fold.
Grommets: hanging hardware that also holds the edge
Grommets are the metal rings set into a banner's edge so it can be tied, hooked or zip-tied in place. The Avery Dennison bulletin points out that they do two jobs: they serve for hanging, and they add strength to the edge, whether that edge is hemmed or left unfinished.
Not all grommets hold equally. The bulletin warns that cheap grommets held only by an overlapping tab can pull out in strong wind. The strongest type is the spur grommet, which has spikes that wedge into the banner material, and that is the type Avery Dennison recommends for heavy duty banners.
The number of grommets also scales with the job. Per the bulletin, a short temporary banner can skip hemming and use only a few grommets, while long-term or high wind installations need more grommets and strong hems. More attachment points spread the load, so no single grommet carries the whole force of a gust.
When you order, say how the banner will be attached (zip ties to a fence, rope to poles, hooks on a wall) and ask the printer to confirm on the quote which grommet type will be used and where they will be placed. If the banner is going somewhere windy, ask specifically whether spur grommets are available.
Why wind slits often backfire
Wind slits are the half-moon or U-shaped cuts some people request so air can pass through a banner instead of pushing against it. The logic sounds reasonable, but Avery Dennison's banner bulletin does not recommend them, for a specific reason: every slit is an unfinished edge in the middle of the banner, and unfinished edges are weak spots. Constant flexing, combined with cold temperatures, may cause those cuts to tear and fray.
In other words, a wind slit swaps one problem for another. It may reduce how hard the wind pushes on the banner, but it introduces dozens of small places where a tear can start, each one flexing every time the wind moves the material. Once a slit starts to run, the damage can spread well beyond the cut itself.
The bulletin's alternative is to address wind directly: choose enough strength in the material (denier and scrim) and use supporting fixtures suited to higher wind. It also states plainly that high wind areas require a heavy duty banner product. If you are worried about wind, the better request is usually a stronger material, stronger hems, more and better grommets, and a sturdier mounting, rather than cutting holes in a banner that was not built for the conditions.
If you do want air to pass through, ask your printer whether a mesh banner material suits your design and location. That is a different material choice, not a modification of solid vinyl, and the shop can tell you how it would print.
Matching the build to wind and duration
Two questions drive almost every finishing decision: how long will the banner be up, and how much wind will it face? Here is how the guidance plays out across common situations.
- Short indoor use, such as a registration table backdrop or a booth sign for a weekend event: wind is not a factor. Per the Avery Dennison bulletin, a short temporary banner can skip hemming and use only a few grommets. A taped or welded hem is an option if you want a cleaner edge for appearance.
- Short outdoor use in a sheltered spot, such as a sign on a wall at a single-day festival: hems and a sensible number of grommets protect the edge from the handling and light wind it will see. This is where to talk through your hanging method with the printer.
- Long-term outdoor use, such as a fence banner meant to stay up for months: the bulletin calls for more grommets and strong hems. This is where reinforced options like webbing are worth asking about.
- High wind exposure, such as an open lot or an elevated mounting: the bulletin is clear that a heavy duty banner product is required, alongside enough denier and scrim strength, strong hems, spur grommets and supporting fixtures. Skip the wind slits.
For event signage, see the event and special occasion printing page. For outdoor and long-term installations, the banners and signs page and the large-format printing page cover the product range.
What to put in your banner request
Most banner reprints come from a mismatch between the build and the conditions, not from a printing defect. A complete request heads that off. Include:
- Finished size, and whether it is indoor or outdoor.
- Where it will hang and how much wind it will face, described plainly.
- How long it needs to last.
- How it will be attached: zip ties, rope, hooks, poles or a frame.
- The hem style you want, or a request for the printer's recommendation.
- The grommet type and placement, and whether spur grommets are available.
- Whether you need a single-sided or double-sided banner.
Then watch for these common mistakes:
- Ordering wind slits as a fix for a windy site instead of upgrading the material and hardware.
- Choosing light material and minimal grommets for a banner that will stay up long-term outdoors.
- Placing text, logos or QR codes inside the hem band, where stitching and grommets will cut through them.
- Assuming a material's unprinted durability rating applies to the finished, printed banner.
- Leaving hem allowance unconfirmed, so the banner finishes at the wrong size.
If you are unsure how your situation maps to these choices, describe the installation when you contact the print shop and ask for the material, hem and grommet specification to be written on the quote. Having it in writing means everyone agrees on what is being built before it goes to print.